RealFlight G3 and the G3 Expansion Pack1 The best of both worlds! Combine RealFlight G3 with the G3 Expansion Pack 1, and Great Planes best selling R/C flight simulaotr gets even better. G3 Expansion Pack 1 software was written exclusively for the G3 by the creators of G3 - the people most qualified to exploit and enhance its unique performance p[Read More]
Features and Benefits
* 7.2V 2300mAh NIMH rechargeable battery pack
* Made of 6 AA NIMH 2300mAh rechargeable batteries in 2x3 configuration
* Ideal Rechargeable Battery Pack for light weight walking Robot, RC planes (Hightec, JR and Futaba) and RC cars.
* NiMH technology enables convenient charging at any time. No cell memory effect. No need t[Read More]
This is the RealFlight Expansion Pack 4 from Great Planes. / / FEATURES: Adds 12 new airplanes, 4 new helicopters and 4 new flying sites / Compatible only with RealFlight G3 and above software / / INCLUDES: Airplanes; / Top Flite B-25J Mitchell Great Planes Yak 54 / Great Planes deHavilland Mosquito MiG 15 / ElectriFly Headwind B [Read More]
The lift on an RC electric plane is moving surfaces, so it must be articulated. The lift control aircraft and climb rates dive, improper installation could result in disaster for the plane. There are several ways to install this vital part of the airplane according to the materials used and the form of a lift. For this article, we assume that the RC electric plane is made of balsa wood.
Instructions
Things you need:
Balsa
Hinge material
Check the alarm
Glue
Sandpaper
Hobby knife
Assembly
RC electric plane
Step
1
Join the 2 halves together stabilizer, if necessary. Many elevators are divided into two RC airplanes, meets the helm. Align the elevator with the stabilizer to ensure that the lift will be the right length of membership. If your plane does not have a split lift skip this step.
Step
2
The position of the elevator next to the stabilizer and mark where your hinges will be installed. Be sure to mark both the depth and the horizontal stabilizer.
Step
3
Use sandpaper and smoothing the edge of a lift. The diamond should look like this “when finished. This allows the elevator to move freely in both directions.
Step
4
Make incisions in the stabilizer and the elevator of the breadth and depth of the hinge. Be careful to cut the slot axis and not in a right angle. This is the hardest part of the installation that you normally work with widths that are ? inch or less.
Step
5
Flood the stabilizer and elevator again. Keep in mind that you will need to cut some cover the dough up front stabilizer
Step
6
Place the elevator and stabilizer into the appropriate slot in the fuselage. It helps to put the first aircraft shared elevator lift.
Step
7
Align the stabilizer and glue in place. Make sure the stabilizer is centered before pasting. Measure the distance from wing tip to tip the lift on each side, they must be the same.
Step
8
Hinges glue the stabilizer. Make sure the hinges move freely and without glue destruction.
Step
9
Glue the elevator hinges. Again make sure that the pin moves freely and without glue was fouled.
Step
10
Install the elevator control horn. Make sure the holes on the horn are aligned with the pivot hinge. Connect the pushrod to the Horn of control. This completes the installation of lifts.
Shaft Diameter: 3 mm (0.118 in) Fits GWS type gearboxes
EPP1045 counter rotating pair: 1 left hand & 1 right hand rotation
The description of EPP1045 product is a set of anti-aircraft propellers for RC perfect for use in aircraft engines and single or multiple coaxial RC helicopters RC. You get 2 draft: a proposal for CW turns clockwise and the other proposal rotates counterclockwise counterclockwise (1 left and 1 right hand rotation). The rotor blades are paired difficult to find in Paris has found against the pairs of rotation. The length is 10 inches and the height is 4. 5 inches per revolution. Specifications for EPP1045 EOC. . . More>>
The Exceed RC EDF Jet F/A-18C aircraft from Nitro is available in RTF and ARF versions. The 31 "main advantages of a Jet Blue Angels finish and 70 mm brushless EDF, which is now powered by a 4-cell LiPo pack ….
