Archive for the ‘rc electric plane’ Category
One of the fastest growing hobby in the world today is building and flying an RC plane homemade. Nothing beats the feeling of satisfaction that you get to fly the plane fine paid hours of hard work in construction. This type of project is ideal for individual or group and family activities. You can enjoy your flight with fans of another RC Electric plane joining a club or organization that the days of the planned flight and contests.
Instructions
Things you need:
RC Airplane Kit
Screwdrivers
Screws
Safety glasses
Glue
Wiring Tools
plastic containers
Step
1
Choose an RC Electric plane kits cost that fits your budget and meets your level. The type of kit you choose will be largely determined by the amount of money you are willing to spend and the complexity of the model.
Step
2
Empty space in the garage or basement. You will need a lot of space to store and work your plan is protected from the elements and keep out of the hands of children. Be sure to choose a place that is warm and dry, and a place that is organized and well run.
Step
3
Get all the tools you need for this project, organize and store your work. You will need a range of instruments such as strippers, glue, sandpaper, goggles and grips. Sure they are all at your fingertips while you work on your aircraft, keep them clean and remember to put in place, so as not to lose them.
Step
4
Organize all the documentation that came with the kit plane enthusiasts. For example, put all the wheels and wheel tracks in a single stack, propeller, and his piece in a stack, and so on. Store them in plastic containers to keep them separate. This will reduce the risk of losing your important documents and having to spend more money to replace them.
Step
5
Read all the instructions, after each step explicitly you start your house RC Electric plane. These step-by-step instructions guide you through the process of assembly of the aircraft, and connecting the motor and electronics in the plane properly.
Step
6
Be careful with bullets in the body of the RC Electric plane that you build the plan. If you find any, make sure to use a piece of sandpaper to smooth the rough edges.
Step
7
Paint your RC plane again. This is where your personal creativity comes into play. Design and paint your aircraft in any color you want and give a touch of fantasy.
Step
8
Take your RC Electric plane with a tower, and make sure that all components are working properly. If the plan is not working properly, see the instructions for troubleshooting.
Tags: plane, RC Plane
How to install a lift on an RC electric plane
The lift on an RC electric plane is moving surfaces, so it must be articulated. The lift control aircraft and climb rates dive, improper installation could result in disaster for the plane. There are several ways to install this vital part of the airplane according to the materials used and the form of a lift. For this article, we assume that the RC electric plane is made of balsa wood.
Instructions
Things you need:
Balsa
Hinge material
Check the alarm
Glue
Sandpaper
Hobby knife
Assembly
RC electric plane
Step
1
Join the 2 halves together stabilizer, if necessary. Many elevators are divided into two RC airplanes, meets the helm. Align the elevator with the stabilizer to ensure that the lift will be the right length of membership. If your plane does not have a split lift skip this step.
Step
2
The position of the elevator next to the stabilizer and mark where your hinges will be installed. Be sure to mark both the depth and the horizontal stabilizer.
Step
3
Use sandpaper and smoothing the edge of a lift. The diamond should look like this “when finished. This allows the elevator to move freely in both directions.
Step
4
Make incisions in the stabilizer and the elevator of the breadth and depth of the hinge. Be careful to cut the slot axis and not in a right angle. This is the hardest part of the installation that you normally work with widths that are ? inch or less.
Step
5
Flood the stabilizer and elevator again. Keep in mind that you will need to cut some cover the dough up front stabilizer
Step
6
Place the elevator and stabilizer into the appropriate slot in the fuselage. It helps to put the first aircraft shared elevator lift.
Step
7
Align the stabilizer and glue in place. Make sure the stabilizer is centered before pasting. Measure the distance from wing tip to tip the lift on each side, they must be the same.
Step
8
Hinges glue the stabilizer. Make sure the hinges move freely and without glue destruction.
Step
9
Glue the elevator hinges. Again make sure that the pin moves freely and without glue was fouled.
Step
10
Install the elevator control horn. Make sure the holes on the horn are aligned with the pivot hinge. Connect the pushrod to the Horn of control. This completes the installation of lifts.
Tags: planes, rc electric plane
His first flight in your RC electric plane should be well planned as possible. Do not want to stop the RC electric plane on its maiden voyage.
Instructions
Step
1
Choose a location with sufficient space. The size of your RC electric plane will determine where to run. More aircraft more space you need. If a club near you, contact a member and if it is OK to start the plan for their airstrip.
A small plane electric rc May will be shipped in a large park.
Step
2
Make sure that the wind is not strong. Preferably, there should be a minimum of wind. You must run your plane in the wind. So be prepared to handle the radio controls. If you have practiced before a flight simulator, you should not encounter much difficulty in controlling the aircraft.
Step
3
Keep the airplane at all times a clear vision. Do not let it leave your sight and be very careful in the sun in your eyes.
Step
4
I remember an airplane rc electric batteries to be fully charged before the theft and to ensure that the flight time.
Tags: plane, rc electric plane
Flying remote control or RC Electric planes
The air is a hobby more and more fans in flight. Improvements in technology make exciting RC airplanes available in all price ranges. Landings are in pain and pleasure to fly RC Electric plane. Trying to bring your plane down in one piece, but remember to put safety first.
Instructions
Step
1
Landing an RC plane in an emergency the same way you land in non-emergencies. Turn your plane into the wind and cut the engine. Landing in a crosswind are acceptable. Use your rudder to keep the flight path and straight off the plane to slide gently to the ground. Use your engine gently rates affect your aircraft decent if you like. Pull the control stick or worse, immediately prior to landing the aircraft landed with its nose in the air.
Step
2
Beware of power lines, cars, people and other RC planes when you make an unscheduled landing. Use what you have control plan to prevent injury to others or their property. The arrests are part of the RC hobby.
Step
3
Buying an RC plane made especially to withstand the forced landing, if you’re new to the hobby or practice new skills. Aircraft crash resistance are available from your local retailers or online RC Electric planes.
Step
4
Keep the batteries fully charged. Being aware of the limits of power during flight. Land immediately if your RC plane is also in danger of a battery dying.
Step
5
Enter your name and phone number on your unmanned, which lands in a remote area. Posts Check to see if a citizen in question is your RC Electric planes and contacts.
Tags: plane, RC Plane
There are two ways to cover a balsa wood airplane remote control. The first is
with butyl rubber and fabric or silk. The second is to use an iron on film or
tissues. Both methods provide a final test of fuel that will last for years, if
adequately supported. Since the butyl rubber is flammable and dangerous to breathe, most
modelers to choose a flat iron on a film to cover their planes.
Instructions
Things you need:
Sandpaper Hobby heat gun Gloves Trim iron leaves Sharp hobby knife
RC Electric planes
Step
1
Choose a color scheme. This may sound simple, but it is important to know what
you want your floor to look like before you start. Read the movie Iron
instructions before you begin.
Step
2
Sand all surfaces with fine sandpaper. This will help to achieve good
End. Make sure that no glue oozing from the joints, as this may cause
unsightly stains on the cover.
Step
3
Apply the lining of the upper arm of iron pastime. Only one
half of the wing at a time. The film-Tack to the edge of the wing
and pull the film has taught. Tack the film down on the trailing edge. Now, use the
heat gun to remove any wrinkles
Step
4
Cover the bottom of the wing with the same technique. Work gloves for use
protect your hands from the heat gun. Trim any excess film with your hobby
knife. Repeat these steps for the other half of the wing panel.
Step
5
Cover the fuselage later. Most of the fuselage must be covered by a series of small
pieces of film, rather than a few large. Use the pieces of iron and solid
the heat gun on an open framework.
Step
6
Apply the coating to the elevator and rudder before installing the hinges. This
You can cover all surfaces. Remove the cover areas
must be glued and glue the horizontal stabilizer and vertical
place.
Step
7
Glue in the hinges and mount the horns of control, according to plan. Check
horns must be located near the hinge line for optimal performance.
Step
8
Use the leaves to add color accents trim the airplane. Trim leaves and Peel
Stick and does not require an iron or a heat gun. Trim leaves of different colors can be
used together to make multicolored banners.
Step
9
Transparent film on a glider wing
Use a transparent film to show the structure of the plane. These films
generally thinner and lighter and very good for a glider.
Hello RC Electric planes!
Tags: electric, RC Plane
This article explains how to perform a pre-flight check on a RC Electric plane to secure your RC RC Electric plane will take off, fly and land safely. A pre-flight check must be performed before each flight to avoid crash of a RC Electric plane of $ 200 due to a simple problem like a screw loose.
Instructions
Things you need:
RC AirRC Electric plane
Radio system for aircraft
Various instruments for aircraft
Voltmeter
Step
1
Plated frequency of the club to ensure that no one else is on your channel. Place your card, PIN or sheets of whatever your club uses to designate the channel is in use on the table of frequency.
Step
2
Turn on the transmitter. Verify that the voltage of the battery problem is greater than the rated voltage of the battery. If a 9.6V battery pack, make sure that the voltage is above 9.6V. Some broadcasters to show this as a bar chart or similar measures. If the meter or graph below are half-way, charge the battery in the transmitter before the flight.
Step
3
Check the battery voltage of the receiver. Using a voltmeter, verify that the voltage exceeds the rated voltage of the battery. If it is below the nominal voltage, charge the battery before the flight.
Step
4
Make sure all screws and connections are tight.
Step
5
Make sure all the tread is closed, and their servants or fuel lines on them to prevent them from opening.
Step
6
Verify that the propeller on the engine / motor shaft tight.
Step
7
Turn on the air.
Step
8
Move the aileron stick right. Standing behind the airRC Electric plane, verify that the right wing should rise and the left wing is down.
Step
9
Move the aileron stick left. Verify that the left wing to get up and the right wing is down.
Step
10
Move the elevator stick down. Verify that the elevator descends.
Step
11
Move the elevator stick Up. Verify that the elevator halls.
Step
12
Move the rudder stick right. Check that the rudder is fine. If the aircraft is equipped with a tricycle landing gear, make sure that the front nose wheel is right.
Step
13
Move the rudder to the left analog stick. Check that the rudder moves to the left. If the aircraft is equipped with a tricycle landing gear, make sure that the front nose wheel is on the left.
Step
14
If your fuel aircraft engine, move forward on the accelerator. Check that the carburetor opens. If your RC Electric plane has an electric motor, keeping the air and pass the gas forward. Make sure the engine is running the right direction and goes full throttle.
Step
15
Move throttle back to low. Make sure the carburetor is closed or the engine stops turning.
Step
16
Check the extent of the radio system. If the issuer has a folding antenna, the collapse of the antennas as possible. Foot, at least 100 feet away from the aircraft. Move the aileron and / or sticks deep and verify that the moving surfaces. If the issuer does not have a folding antenna, follow the instructions provided by the manufacturer of the transmitter.
Step
17
If the aircraft has a gasoline engine, fill the fuel tank and control does not leak.
Step
18
Check the battery voltage of the transmitter and receiver pack Again. If one is low, the battery may not have the capacity for a long flight. Do not use the battery. Replace with new battery fully charged.
Step
19
Fly fishing and fun!
Tags: plane, RC Plane
Until recently, RC (radio controlled) planes were not sold in ready-to-fly form. Consequently, purists prefer to build their own RC Electric planes s RC Electric planes . If it can be difficult to assemble hundreds of parts in a car that flies in fact, those who practice the art of saying it provided a much more satisfying.
Instructions
Things you need:
RC Electric planes (dismantled)
Screwdriver to the head of the case (s)
Pliers
Safety glasses
Knives
Sandpaper and a sanding block (recommended for aircraft wood RC)
Saw
Industrial strength glue
Wire-strippers (Recommended for RC aircraft with electric motor)
Assemble an RC Airplane
RC Electric planes
Step
1
Read the instruction manual very carefully. Pay particular attention to the phases of shares of mechanical assembly processes. Make sure you have a global vision of all stakeholders. If you have any questions before you start, consult the staff of the store where you purchased the RC airplane kit, or call the manufacturer.
Step
2
Gather all necessary documents and group them by type (such as screws or Windows) or by function (like the pieces necessary to assemble the wings and landing gear). Store them in boxes or in the drawer because it is based to ensure they are not irrelevant.
Step
3
Work slowly and follow the instructions in your instruction manual to the letter. See the patterns to ensure that what you have built so far seems to be the way it should. Absolutely sure that you have completed each step correctly and completely before proceeding to the next.
Step
4
Sand each chip to lose if your RC Electric planes is made of wood. You must perform this step is also constructed to minimize the risk of catching a splinter that you continue your assembly.
Step
5
Choose and apply a coating of attractive cover. These can be made of cloth, silk, fiberglass or plastic. Remember, they are not necessarily related to use any coatings included in the RC Electric planes kit, because they can be customized for a relatively inexpensive cost.
Step
6
Paint your RC Electric planes using an airbrush. This is easier and works better with the materials used in coatings applied finishing brush.
Tags: plane, RC Plane
